The Block and Bleed Fuel Gas Collection System is typically used in conjunction with a capacitance probe. The Block and Bleed allows the removal of the probe on the fly without shutting down the entire vessel. From time to time it is necessary to remove the controls to service, clean, or change them out. This would normally require a complete shut down and drain of the vessel, the Block and Bleed Fuel Gas Collection System allows a vessel to keep producing without the hassle of shutting down. Available in carbon steel, stainless steel, and aluminium. The Block and Bleed has a standard set up; however, we can customize setups in accordance to our customers...
Innovel Pneumatic Chemical Injection Pumps operate using air or natural gas as the driver to inject chemicals into a system. The IT-5100 is similar to a Textsteam* 5100, with improvements to the design and function. The REP-301/ 401 is a piston driver pump, which reduces the amount of gas required to drive the unit. The diaphragm is what the air or natural gas acts on to operate the pump plunger, the units we use are industry standard. *Texsteam is a registered trademark of Texsteam Inc. is not affiliated with McMath Controls & Automation Inc. in any manner. Texsteam Inc has not reviewed, sanctioned or endorsed any products manufactured, reconditioned or sold by McMath Controls & Automation...
Innovel cathodic protection works in prevention or reduction of corrosion in a vessel that a sacrificial anode is used in. Innovel Cathodic Protection are available in aluminium, zinc, or magnesium. All three materials are industry standard in cathodic protection. The Innovel Anode Flanges are what the anode is installed on and bolted into the vessel. We stock standard industry set ups; however, we can custom make them to our customers specifications. Carbon (CS A-106) is the standard material used, we can also provide stainless steel 303, 304,...
The Innovel Surge Tank/ Collection Bottle is used to steady out a pulsating supply source. An example would be the discharge from a chemical injection pump, which then allows for a controlled steady state supply of gas which can then be used to supply other sources. This is accomplished by connecting the pulsating source to the inlet of the surge tank which then acts as a buffer to smooth out the source and discharge the gas at a controlled rate and pressure. A secondary function of the unit is that it will also help to alleviate water from the supply gas. This gas can then be used to supply the heaters or other instrumentation, thus saving gas and reducing emissions to the atmosphere. These units have an internal diameter of 3” and are 26” in length. They are constructed of aluminum and come complete with pressure gauges, regulator, relief valve, fittings and valves to allow for an out of the box installation. In most applications the surge tank is able to utilize all the emission from the chemical pump to supply the heaters. This allows for a far less costly and more effective alternative to solar...
Within a few strokes, the McMath Baker Hand Injection Pumps can effectively deice valves or lines. These portable units are available in two different sizes 20L (5 Gallon), or the compact 10L (2.5 Gallon) model. The McMath Baker Hand Injection Pumps are available in 1000, 3000, 10000 psi. The Baker Hand Injection Pumps can also be used for pressure testing. McMath Controls stocks all units in our Edmonton warehouse, along with repair kits for all makes and models of baker pumps. Yes, including our competition’s models for half the cost. Models Available Hand Pump 20L ITLP-1K-20L MC Low Pressure Hand Pump- 1000 psi 20L ITHP-3K-20L MC High Pressure Hand Pump- 3000 psi 20L ITHP-10K-20L MC High Pressure Hand Pump- 10,000 psi 20L Hand Pump 10L ITLP-1K-10L MC Low Pressure Hand Pump- 1000 psi 10L ITHP-3K-20L MC High Pressure Hand Pump- 3000 psi 10L ITHP-10K-10L MC High Pressure Hand Pump- 10,000 psi 10L 20 L 1000, 3000, 10000 psi 10 L 1000, 3000, 10000 psi...
